76 Fuel Injection System Function right hand bank.36 EGR Control-Back Pressure Transducer.11 Crank Angle Sensor/Camshaft Position Sensor.Diagnostic Display Code 0-1 should be indicated. Turn ignition On, then observe Overheat Warning Lamp and Buzzer. Remove connector or jumper wire from reset switch electrical connector.Ĭonnect electrical connector to reset switch. The System memory will be cleared in approximately 10 seconds. The reset switch is located behind the electrical unit board.Ĭheck that Overheat Warning Lamp and Buzzer display shows Diagnostic Display Code 0-1.
Nissan UD Diesel: Clearing Diagnostic Trouble Codes MID-TICS SystemĬheck that Overheat Warning Lamp is displaying Diagnostic Display Code.Ĭonnect memory clear connector 2400400Z09, or a suitable jumper wire to reset switch terminals. The trouble codes will be displayed by the flashing Engine Control Lamp and the Overheat Warning Lamp and the Overheat Warning Buzzer. Place diagnostic switch in the Off position.Ĭarry out diagnosis under the following three conditions: Nissan UD Diesel: Accessing Diagnostic Trouble Codes ID-TICS System Each trouble code will be displayed 3 times before the next trouble code is displayed. For example, a code 12 will be displayed by the Check Engine lamp flashing 1 time for approximately 1.2 seconds, followed by a. The diagnostic trouble codes will be displayed by the Check Engine lamp.
If you need to update your carprog full v4,v5,v6.8 or v7.28 to V8.21 online version,you can buy the V8.21 carprog main unit without buying the full 21 adapters.Nissan UD Diesel: Diagnostic Trouble Code Interpretation MID-TICS System Select M35-> 35080-> read/ verify, then click OKĬlick the fourth icon on the top icon column for initialization
Part 2 – Carprog v8.21 read EEPROM M35080Īutomatically installing device driver software… Run Carprog 8.21 interface automatically, then close it
Send the hardware ID to the dealer to get the activation code Part 1 – Carprog 8.21 activation & installationĮstablish a new folder named “8.21” on DesktopĬopy all the files in carprog 8.21 DVD disk (E:) to the new folder “8.21” on Desktop
How to install Carprog full 8.21 online version? Here is the instruction on installing and activating Carprog V8.21 perfect online version China clone on Windows 7 operating system by engineer. Use with all cars complained with OBDII standard)ġpc x D1 - Odometer-airbag Adapter (Dashboard ,Airbag programming adapter )ġpc x A3 - Transponder Antenna (Used with all CARPROG immobiliser software)ġpc x A10 - Motorola Adapter Cable (Motorola MCU programming adapter)ġpc x A11 - BMW EWS Adapter Cable (Used with BMW Immo software)ġpc x A16 - Car radio Cable (Used for Opel, Renault, Peugeot, Citroen car radio made by Philips decoding)ġpc x A15 - Cable (Used with D1 adapter, Universal car dashboard and airbag programming adapter )ġpc x A17 - Honda Airbag OBD2 Cable (Adapter for Honda airbag reset by OBDII )ġpc x A4 - Eeprom Adapter Cable (Used for eeprom programming)ġpc x A5 - DIP8 Clip Cable (DIP8 Clip for eeprom programming)ġpc x A6 - SOIC8 Clip Cable (SOIC8 Clip for eeprom programming)ġpc x A7 - MB 38-Pin Cable (Used with MB Airbag and dashboard software)ġpc x A8 - BMW 20-Pin Cable (Used with BMW airbag and dashboard software )ġpc x RNS510 Adapter Cable (RNS510 radio decoding interface cable )ġpc x VOLVO FORD CAN 2006+ Cable (Needed for airbag and dashboard programming)ġpc x FIAT CAN 2006 Cable (Needed for airbag and dashboard programming) Work 100%ġpc x A1 - OBD2 Adapter Cable (Inside have K-line and CAN bus switches. dash with HC08 and NEC processors with A10 cable without disamble the dash. Work fine for Renault Scenic, Laguna, Megane. I use both because clone is good for some airbags and opel ecu via obd.it's pretty good tool. Started with clone 4.01, after that bougt 4.74 clone and after a year i bought original dashboard pack. error connectionĬlio3 2006 dash with 24c04 always change to 137000 0r 131000km cant remember by obd.Īstra IV, insignia, octavia 2011 JC online work
While carprog 10.05 as a plug-and-play kit, is more convenient to use.Ĭarprog v8.21 has different serial number as carprog v10.05/v7.28.Ĭarprog Full V8.21 Firmware tested ok on: With ECU-OPEL, OPEL CAN, PSG16, OPEC28 software.Īutomatically get token renew after it used upĬarprog v9.31 read and erase BMW EEPROM M35080Ĭarprog v 8.21 is the best option for the most vehicle coverage and online use,
So that it support the most vehicle models. V10.05 Carprog’s firmware is authorized more cars RNS510 - Navigation decoding tool by Navi diagnosticĬarprog full V7.28 vs.